Mesauda MNP Full Coverage Tips Mandorla 240 pz - soak gel tips for nail reconstruction

Application of Tips & Base Coat
Select the correct size of the full coverage tips: you need to cover the nail perfectly, from one side to the other. If necessary, choose a larger size and gently file the edges to match the natural nail.
Using the drill and the diamond trapezoid tip (or the 180 abrasive cylinder) matt the inside of the tip, at the area that will be placed on the natural nail. Remove the dust by wiping with a pad soaked in MNP UV Gel Cleanser.
Carry out a perfect manicure, matting the natural nail with a buffer or a 180 grit file and apply the preparers (first MNP Nail Prep, then MNP Ultrabond) letting them both air dry for 30 seconds.
Apply the preferred MNP base coat on the natural nail and cure in a UV/LED lamp for 1/2 minutes.
Apply a thin layer of MNP Ultrabond inside the tip, on the previously matted area, and allow to air dry.
Apply a drop of base coat preferably rubber (MNP Universal Base or MNP Fiber Base) inside the tip.
Bring the tip close to the nail, maintaining an angle of approximately 45° from the cuticle area. Then press the tip lightly onto the nail, while spreading the base to cover the space between the tip and the nail.
Carry out an initial polymerisation with a one finger lamp for 10 to 15 seconds, holding the tip on the nail.
Finish the polymerisation under a UV/LED lamp for a further 60 seconds.
Pass a pad soaked in MNP UV Gel Cleanser over the tip, making sure to also pass it under the free edge. If necessary, shorten the length with the file.
Gently file the cuticle area of the tip, lowering it until it blends perfectly with the natural nail. Buff the surface of the tip, dust with MNP Kabuki Nail Duster and clean again with a pad soaked in MNP UV Gel Cleanser.
You can now proceed with the application of your favourite gel polish (MNP, ME, TOP NOTCH) as per protocol.
Seal with the preferred top coat (MNP, ME, TOP NOTCH) as per protocol.

Tips&Builder Gel application
Select the full coverage tips of the correct size: it is necessary to cover the nail perfectly, from one side to the other. If necessary, choose a larger size and gently file the edges to match the natural nail.
Using the drill and the diamond trapezoid tip (or the 180 abrasive cylinder) matt the inside of the tip, at the area that will be placed on the natural nail. Remove the dust with a pad soaked in MNP UV Gel Cleanser.
Carry out a perfect manicure, matting the natural nail with a buffer or a 180 grit file and apply the preparers (first MNP Nail Prep, then MNP Ultrabond) letting them both air dry for 30 seconds.
Spread the preferred MNP base (Bonding Base, Universal Base, Fiber Base or Genie in a Bottle Base if using Genie in a BottleTM ) on the natural nail and cure in a UV/LED lamp for 1/2 minutes.
Apply a thin layer of the chosen builder on the natural nail and polymerise under a UV/LED lamp for 1/2 minutes. Please note: Full coverage tips can only be removed with a remover wrap if you decide to use Genie in a BottleTM.
Apply a thin layer of MNP Ultrabond to the inside of the tip, on the previously matted area, and allow to air dry.
Release a small amount of the chosen builder inside the tip, at the cuticle edge.
Move the tip closer to the nail, maintaining an angle of approx. 45° from the cuticle area. Then press the tip lightly onto the nail, while spreading the builder so that the space between the tip and the nail is covered.
Carry out an initial polymerisation with a one finger lamp for 10 to 15 seconds, holding the tip on the nail.
Finish the polymerisation under a UV/LED lamp for a further 60 seconds. Be careful not to spill the product, avoiding contact with the cuticle.
Pass a pad soaked in MNP UV Gel Cleanser over the tip, making sure to also pass it under the free edge. If necessary, shorten the length with the file. Gently file the cuticle area of the tip, lowering it until it blends perfectly with the natural nail. Buff the surface of the tip, dust with MNP Kabuki Nail Duster and clean again with a pad soaked in MNP UV Gel Cleanser.
You can now proceed with the application of your favourite gel polish (MNP, ME, TOP NOTCH) as per protocol. If you want to leave the transparent effect, we recommend applying the full coverage tips with a pink cover builder.
Seal with your favourite top coat (MNP, ME, TOP NOTCH) as per protocol.
- Refill

MNP full coverage tips also allow refills. Here are the steps to follow:
Remove the colour or finish from the tip.
Carry out a perfect manicure on the uncovered portion of the natural nail, finishing with the application of MNP Nail Prep and MNP Ultrabond, leaving them both to air dry for 30 seconds.
Spread the preferred MNP base (MNP Bonding Base or Genie in a Bottle Base) on the uncovered portion of the nail and cure under a UV/LED lamp for 1/2 minutes.
Fill in the regrowth, using the reconstruction system previously used for applying the tips, and polymerise under a UV/LED lamp for 1/2 minutes.
Remove the dispersion using a pad soaked in MNP UV Gel Cleanser and shape by filing. Remove the dust using MNP Kabuki Nail Duster and then wipe off with a pad soaked in MNP UV Gel Cleanser.
Apply the desired finish and cure in a UV/LED lamp for 1/2 minutes.
- soak off removal
(Can only be done if the tips were applied using only the base or the Genie in a BottleTM soak off builder).
Cut the free edge you wish to remove.
Reduce the thickness using a file or drill.
Apply the aluminium removal sheets after soaking the pad on them with MNP Soak Off Remover.
Wait approx. 15 to 20 minutes (depending on the thickness of the product on the nail) and then remove the aluminium sheets one at a time, pushing off the residue with the nail pusher.

Set of 240 pieces in 12 sizes. Transparent colour.